Imported Upstream version 2.11.00.021.0
This commit is contained in:
Mario Fetka
372
msg/tdm_msg_en
Executable file
372
msg/tdm_msg_en
Executable file
@@ -0,0 +1,372 @@
|
||||
#0x13:344
|
||||
0x0000:"Are you sure you want to logout?"
|
||||
0x0001:"NO CONTROLLERS"
|
||||
0x0002:"NOT COMPATIBLE"
|
||||
0x0003:"Controller ID"
|
||||
0x0004:"Last updated "
|
||||
0x0005:"This page will automatically refresh every "
|
||||
0x0006:" minute(s)"
|
||||
0x0007:"version "
|
||||
0x0008:"Please wait a moment while you are redirected to the new port........"
|
||||
0x0009:"NO UNITS"
|
||||
0x000A:"OK"
|
||||
0x000B:"WARNING"
|
||||
0x000C:"ERROR"
|
||||
0x000D:"Unit"
|
||||
0x000E:"Type"
|
||||
0x000F:"Capacity"
|
||||
0x0010:"Port"
|
||||
0x0011:"NO DRIVES"
|
||||
0x0012:"Stripe"
|
||||
0x0013:"Background Task Rate unchanged"
|
||||
0x0014:"Background Rebuild Rate unchanged"
|
||||
0x0015:"Failed to change Background Task Rate"
|
||||
0x0016:"Failed to change Background Rebuild Rate"
|
||||
0x0017:"Changed Background Task Rate to "
|
||||
0x0018:"Changed Background Rebuild Rate to "
|
||||
0x0019:"Background Verify Rate unchanged"
|
||||
0x001A:"Failed to change Background Verify Rate"
|
||||
0x001B:"Changed Background Verify Rate to "
|
||||
0x001C:"Auto verify policy unchanged"
|
||||
0x001D:"Disabled auto verify on Unit "
|
||||
0x001E:"Enabled auto verify on Unit "
|
||||
0x001F:"Failed to set auto verify on Unit "
|
||||
0x0020:"Continue on Source Error policy unchanged"
|
||||
0x0021:"Disabled Continue on Source Error policy on Unit "
|
||||
0x0022:"Enabled Continue on Source Error policy on Unit "
|
||||
0x0023:"Failed to set Continue on Source Error policy on Unit "
|
||||
0x0024:"Write Cache unchanged"
|
||||
0x0025:"Disabled Write Cache on Unit "
|
||||
0x0026:"Enabled Write Cache on Unit "
|
||||
0x0027:"Failed to set Write Cache on Unit "
|
||||
0x0028:"Rebuild Schedule state unchanged"
|
||||
0x0029:"Rebuild Schedule will be ignored"
|
||||
0x002A:"Rebuild Schedule will be followed"
|
||||
0x002B:"Failed to change Rebuild Schedule state"
|
||||
0x002C:"Verify Schedule state unchanged"
|
||||
0x002D:"Verify Schedule will be ignored"
|
||||
0x002E:"Verify Schedule will be followed"
|
||||
0x002F:"Failed to change Verify Schedule state"
|
||||
0x0030:"Rebuild Schedule slot not deleted"
|
||||
0x0031:"Successfully deleted Rebuild Schedule slot(s)"
|
||||
0x0032:"Verify Schedule slot not deleted"
|
||||
0x0033:"Successfully deleted Verify Schedule slot(s)"
|
||||
0x0034:"Self-test Schedule slot not deleted"
|
||||
0x0035:"Successfully deleted Self-test Schedule slot(s)"
|
||||
0x0036:"Self-test Task state unchanged"
|
||||
0x0037:"Failed to change Self-test Task state"
|
||||
0x0038:"Successfully changed Self-test Take state"
|
||||
0x0039:"Rebulid Schedule slot not added"
|
||||
0x003A:"All Rebulid Schedule slots full, please delete one or more slots before adding"
|
||||
0x003B:"Failed to add Rebuild Schedule slot"
|
||||
0x003C:"Successfully added Rebuild Schedule slot"
|
||||
0x003D:"Verify Schedule slot not added"
|
||||
0x003E:"All Verify Schedule slots full, please delete one or more slots before adding"
|
||||
0x003F:"Failed to add Verify Schedule slot"
|
||||
0x0040:"Successfully added Verify Schedule slot"
|
||||
0x0041:"Self-test Schedule slot not added"
|
||||
0x0042:"All Self-test Schedule slots full, please delete one or more slots before adding"
|
||||
0x0043:"Failed to add Self-test Schedule slot"
|
||||
0x0044:"Successfully added Self-test Schedule slot"
|
||||
0x0045:"Cannot remove drive"
|
||||
0x0046:"Failed to remove drive from Port "
|
||||
0x0047:"Successfully removd drive from Port "
|
||||
0x0048:"Cannot stop the Verify"
|
||||
0x0049:"Failed to stop Verify on Unit "
|
||||
0x004A:"Successfully stopped Verify on Unit "
|
||||
0x004B:"Cannot start Rebuild"
|
||||
0x004C:"Failed to start Rebuild on Unit "
|
||||
0x004D:"Successfully started Rebuild on Unit "
|
||||
0x004E:"Cannot start Verify"
|
||||
0x004F:"Failed to start Verify on Unit "
|
||||
0x0050:"Successfully started Verify on Unit "
|
||||
0x0051:"Cannot remove units"
|
||||
0x0052:"Successfully removed unit(s) "
|
||||
0x0053:"Failed to remove unit "
|
||||
0x0054:"Cannot delete units"
|
||||
0x0055:"Successfully deleted unit(s) "
|
||||
0x0056:"Failed to delete unit "
|
||||
0x0057:"Cannot create units"
|
||||
0x0058:"Please select at least one drive to create a unit"
|
||||
0x0059:"Successfully created unit(s)"
|
||||
0x005A:"Failed to create unit with drive "
|
||||
0x005B:"Cannot Rescan controller"
|
||||
0x005C:"Failed to Rescan controller"
|
||||
0x005D:"Rescan found the following unit(s)"
|
||||
0x005E:"Found the following drives(s)"
|
||||
0x005F:"Cannot Migrate unit"
|
||||
0x0060:"Unknown type of unit to Migrate"
|
||||
0x0061:"Successfully started Migrate on unit "
|
||||
0x0062:"Failed to start Migrate on unit "
|
||||
0x0063:"Cannot clear Alarms"
|
||||
0x0064:"Cleared Alarms"
|
||||
0x0065:"Successfully installed new battery"
|
||||
0x0066:"Failed to install new battery"
|
||||
0x0067:"Successfully started battery capacity test"
|
||||
0x0068:"Failed to start battery capacity test"
|
||||
0x0069:"This is a test e-mail generated by 3ware 3DM2"
|
||||
0x006A:"Failed to send test message"
|
||||
0x006B:"E-mail test message sent. If you do not receive an e-mail, check for a valid recipient, sender, and server"
|
||||
0x006C:"E-mail notification status unchanged"
|
||||
0x006D:"E-mail notification disabled"
|
||||
0x006E:"E-mail notification enabled"
|
||||
0x006F:"Unknown setting"
|
||||
0x0070:"E-mail notification settings unchanged"
|
||||
0x0071:"E-mail notification settings successfully changed"
|
||||
0x0072:"E-mail notification severity unchanged"
|
||||
0x0073:"E-mail notification severity successfully changed"
|
||||
0x0074:"Page refresh time unchanged"
|
||||
0x0075:"Disabled automatic page refresh"
|
||||
0x0076:"Minutes between automatic page refresh set to "
|
||||
0x0077:"Remote access state unchanged"
|
||||
0x0078:"Remote Access disabled"
|
||||
0x0079:"Remote Access enabled"
|
||||
0x007A:"Language setting unchanged"
|
||||
0x007B:"Language setting successfully changed"
|
||||
0x007C:"Listening Port unchanged"
|
||||
0x007D:"The port entered is the same as the current port, Listening Port unchanged"
|
||||
0x007E:"Invalid Listening Port specified"
|
||||
0x007F:"Password unchanged"
|
||||
0x0080:"User Password unchanged"
|
||||
0x0081:"User Password successfully changed"
|
||||
0x0082:"Administrator Password unchanged"
|
||||
0x0083:"Administrator Password successfully changed"
|
||||
0x0084:"User now logged in"
|
||||
0x0085:"Administrator now logged in"
|
||||
0x0086:"Unknown login"
|
||||
0x0087:"You are now logged out"
|
||||
0x0088:"Login"
|
||||
0x0089:"No Remonte Access"
|
||||
0x008A:"Summary"
|
||||
0x008B:"Information"
|
||||
0x008C:"Controller Details"
|
||||
0x008D:"Unit Information"
|
||||
0x008E:"Drive Information"
|
||||
0x008F:"Management"
|
||||
0x0090:"Controller Settings"
|
||||
0x0091:"Scheduling"
|
||||
0x0092:"Maintenance"
|
||||
0x0093:"Monitor"
|
||||
0x0094:"Alarms"
|
||||
0x0095:"Battery Backup"
|
||||
0x0096:"Enclosure Support"
|
||||
0x0097:"3DM 2 Settings"
|
||||
0x0098:"Help"
|
||||
0x0099:"Refresh"
|
||||
0x009A:"Select Controller"
|
||||
0x009B:"Refresh Content"
|
||||
0x009C:"ID"
|
||||
0x009D:"Model"
|
||||
0x009E:"Serial #"
|
||||
0x009F:"Firmware"
|
||||
0x00A0:"Driver"
|
||||
0x00A1:"Status"
|
||||
0x00A2:"BIOS"
|
||||
0x00A3:"Monitor"
|
||||
0x00A4:"Boot Loader"
|
||||
0x00A5:"# of Units"
|
||||
0x00A6:"# of Ports"
|
||||
0x00A7:"Download"
|
||||
0x00A8:"active"
|
||||
0x00A9:"paused"
|
||||
0x00AA:"Subunit"
|
||||
0x00AB:"not initialized"
|
||||
0x00AC:"Subunits"
|
||||
0x00AD:"Error Log"
|
||||
0x00AE:"Background Task Rate"
|
||||
0x00AF:"Task Rate"
|
||||
0x00B0:"Rebuild Rate"
|
||||
0x00B1:"Verify Rate"
|
||||
0x00B2:"Unit Write Cache"
|
||||
0x00B3:"Write Cache"
|
||||
0x00B4:"Auto Verify"
|
||||
0x00B5:"Continue on Source Error during Rebuild"
|
||||
0x00B6:"Unit Policies"
|
||||
0x00B7:"Enabled"
|
||||
0x00B8:"Disabled"
|
||||
0x00B9:"Other Controller Settings"
|
||||
0x00BA:"change via BIOS"
|
||||
0x00BB:"Number of Drive per Spin-up"
|
||||
0x00BC:"Delay between Spin-up"
|
||||
0x00BD:"Export Unconfigured Disk"
|
||||
0x00BE:"Disable Write Cache on Unit Degrade"
|
||||
0x00BF:"Close"
|
||||
0x00C0:"Logout"
|
||||
0x00C1:"Change Port"
|
||||
0x00C2:"Select a type of task you would like to schedule"
|
||||
0x00C3:"Rebuild Tasks"
|
||||
0x00C4:"Verify Tasks"
|
||||
0x00C5:"Selft-test Tasks"
|
||||
0x00C6:"Schedule Rebuild Tasks"
|
||||
0x00C7:"Schedule Verify Tasks"
|
||||
0x00C8:"Schedule Self-test Tasks"
|
||||
0x00C9:"Follow Schedule"
|
||||
0x00CA:"Ignore Schedule"
|
||||
0x00CB:"Scheduled Rebuilds"
|
||||
0x00CC:"Scheduled Verifies"
|
||||
0x00CD:"Day"
|
||||
0x00CE:"Time"
|
||||
0x00CF:"Duration"
|
||||
0x00D0:"hours"
|
||||
0x00D1:"Remove Checked"
|
||||
0x00D2:"Add New Slot"
|
||||
0x00D3:"Tasks"
|
||||
0x00D4:"applies to all schedule slots"
|
||||
0x00D5:"Ignored until at least one schedule slot is set below"
|
||||
0x00D6:"Rescan Controller"
|
||||
0x00D7:"This will scan all empty ports for newly inserted drives/units"
|
||||
0x00D8:"Unit Maintenance"
|
||||
0x00D9:"drive"
|
||||
0x00DA:"drives"
|
||||
0x00DB:"Verify Unit"
|
||||
0x00DC:"Rebuild Unit"
|
||||
0x00DD:"Migrate Unit"
|
||||
0x00DE:"Remove Unit"
|
||||
0x00DF:"Delete Unit"
|
||||
0x00E0:"*Before removeing or deleteing a unit, make sure there is no I/O on the unit and unmount it"
|
||||
0x00E1:"Available Drives"
|
||||
0x00E2:"Create Unit"
|
||||
0x00E3:"Stop Verify"
|
||||
0x00E4:"Remove Drive"
|
||||
0x00E5:"Select a drive to use to rebuild and click OK"
|
||||
0x00E6:"NO DRIVES AVAILABLE TO USE FOR REBUILD"
|
||||
0x00E7:"Force Continue on Source Errors"
|
||||
0x00E8:"Selected drives to create"
|
||||
0x00E9:"Drives per subunit"
|
||||
0x00EA:"Cancel"
|
||||
0x00EB:"Unit to Migrate"
|
||||
0x00EC:"Select drive(s) to use to migrate"
|
||||
0x00ED:"Clear Alarms"
|
||||
0x00EE:"Message"
|
||||
0x00EF:"Legend"
|
||||
0x00F0:"INFO"
|
||||
0x00F1:"Battery Backup Information"
|
||||
0x00F2:"Battery Backup Unit"
|
||||
0x00F3:"Battery Install Date"
|
||||
0x00F4:"Battery Voltage"
|
||||
0x00F5:"Battery Temperature"
|
||||
0x00F6:"Backup Capacity"
|
||||
0x00F7:"Last Battery Test Date"
|
||||
0x00F8:"PRESENT"
|
||||
0x00F9:"NOT PRESENT"
|
||||
0x00FA:"Battery Pack"
|
||||
0x00FB:"Install New Battery"
|
||||
0x00FC:"Test Battery Capacity"
|
||||
0x00FD:"E-mail notification"
|
||||
0x00FE:"Send E-mail"
|
||||
0x00FF:"Send Severity and Above"
|
||||
0x0100:"Sender"
|
||||
0x0101:"Recipient(s)"
|
||||
0x0102:"Server(name or IP)"
|
||||
0x0103:"Save E-mail Settings"
|
||||
0x0104:"Send Test Message"
|
||||
0x0105:"Password"
|
||||
0x0106:"Change Passord For"
|
||||
0x0107:"Current Password"
|
||||
0x0108:"New Password"
|
||||
0x0109:"Confirm New Password"
|
||||
0x010A:"Change Password"
|
||||
0x010B:"Page Refresh"
|
||||
0x010C:"Minutes Between Refresh"
|
||||
0x010D:"Remote Access"
|
||||
0x010E:"Allow Remote Access"
|
||||
0x010F:"Language"
|
||||
0x0110:"Select Language"
|
||||
0x0111:"HTTP Settings"
|
||||
0x0112:"Listening Port"
|
||||
0x0113:"User"
|
||||
0x0114:"Administrator"
|
||||
0x0115:"Never"
|
||||
0x0116:"3ware 3DM 2 Help"
|
||||
0x0117:"3DM 2 Online Help"
|
||||
0x0118:"3ware Website"
|
||||
0x0119:"Click Here"
|
||||
0x011A:"Failed to get S.M.A.R.T. data"
|
||||
0x011B:"Please Login"
|
||||
0x011C:"Testing the battery capacity will disable the battery backup unit. Are you sure you want to start the test now?"
|
||||
0x011D:"You do not have a battery backup unit installed, enabling write cache may cause loss of data in the event of power failure. Do you wish to continue?"
|
||||
0x011E:"Please check at least one schedule slot to delete"
|
||||
0x011F:"You may only check one unit to flush write cache"
|
||||
0x0120:"Please check a unit to flush write cache"
|
||||
0x0121:"You may only check one unit to verify"
|
||||
0x0122:"Please check a unit to verify"
|
||||
0x0123:"You may only check one unit to rebuild"
|
||||
0x0124:"Please check a unit to rebuild"
|
||||
0x0125:"Please check at least one available drive to create a unit"
|
||||
0x0126:"You may only check one unit to migrate"
|
||||
0x0127:"Please check a unit to migrate"
|
||||
0x0128:"You may only check one drive to use to rebuild"
|
||||
0x0129:"Please check a drive ot use to rebuild"
|
||||
0x012A:"Please check at least one unit to remove"
|
||||
0x012B:"Are you sure you want to remove the following unit(s)?"
|
||||
0x012C:"Please check at least one unit to delete"
|
||||
0x012D:"Are you sure you want to delete the following unit(s)?"
|
||||
0x012E:"Are you sure you want to clear all alarms?"
|
||||
0x012F:"If you are currently connected from a remote machine, your conncetion will be disabled immediately. Do you wish to proceed?"
|
||||
0x0130:"No one"
|
||||
0x0131:"Are you sure you want to remove the drive from port "
|
||||
0x0132:"Faster Task"
|
||||
0x0133:"Faster Rebuild"
|
||||
0x0134:"Faster Verify"
|
||||
0x0135:"Faster I/O"
|
||||
0x0136:"Sunday"
|
||||
0x0137:"Monday"
|
||||
0x0138:"Tuesday"
|
||||
0x0139:"Wednesday"
|
||||
0x013A:"Thursday"
|
||||
0x013B:"Friday"
|
||||
0x013C:"Saturday"
|
||||
0x013D:"English"
|
||||
0x013E:"Spanish"
|
||||
0x013F:"French"
|
||||
0x0140:"German"
|
||||
0x0141:"Chinese (trad)"
|
||||
0x0142:"Japanese"
|
||||
0x0143:"Italian"
|
||||
0x0144:"logged in"
|
||||
0x0145:"UNKNOWN"
|
||||
0x0146:"VERIFYING"
|
||||
0x0147:"INITIALIZING"
|
||||
0x0148:"REBUILDING"
|
||||
0x0149:"MIGRATING"
|
||||
0x014A:"INOPERABLE"
|
||||
0x014B:"DEGRADED"
|
||||
0x014C:"NO BATTERY"
|
||||
0x014D:"TESTING"
|
||||
0x014E:"CHARGING"
|
||||
0x014F:"FAULT"
|
||||
0x0150:"LOW"
|
||||
0x0151:"HIGH"
|
||||
0x0152:"TOO LOW"
|
||||
0x0153:"TOO HIGH"
|
||||
0x0154:"INSTALLED"
|
||||
0x0155:"NOT INSTALLED"
|
||||
0x0156:"Chinese (simp)"
|
||||
0x0157:"Split RAID 1 mirror into Single Disks"
|
||||
#0x0C:26
|
||||
0x0000:"NO ERROR"
|
||||
0x0001:"Failed to initialize 3DM 2 settings"
|
||||
0x0002:"Failed to create SSL object"
|
||||
0x0003:"Failed to create SSL context"
|
||||
0x0004:"Failed to create listening socket"
|
||||
0x0005:"Failed to start listening socket"
|
||||
0x0006:"Failed to create 3DM 2 engine"
|
||||
0x0007:"Failed to create SSL object upon changing listening port"
|
||||
0x0008:"Failed to create SSL context upon changing listening port"
|
||||
0x0009:"Failed to create listening socket upon changing listening port"
|
||||
0x000A:"Failed to start listening socket upon changing listening port"
|
||||
0x000B:"Mail message is NULL"
|
||||
0x000C:"Failed to resolve mail server host name"
|
||||
0x000D:"Failed to create a socket to mail server"
|
||||
0x000E:"Failed to connect to mail server"
|
||||
0x000F:"Invalid User password entered"
|
||||
0x0010:"Invalid Administrator password entered"
|
||||
0x0011:"Not logged in as Administrator"
|
||||
0x0012:"The two new passwords do not match"
|
||||
0x0013:"You must enable Javascript on your browser for 3DM 2 to run properly"
|
||||
0x0014:"3DM2 uses frames but your browser doesn't support them"
|
||||
0x0015:"The page you have reached is part of a frameset. Please click OK to return to the frameset"
|
||||
0x0016:"Remote Access to 3DM 2 has been disabled. Please connect using the local machine by entering 'localhost' in the URL bar"
|
||||
0x0017:"Scheduling is not supported on this controller model"
|
||||
0x0018:"Battery Backup is not supported on this controller model"
|
||||
0x0019:"Cookies are not enabled! You must enable cookies for 3DM2 to work properly"
|
||||
499
msg/tw_msg_en
Executable file
499
msg/tw_msg_en
Executable file
@@ -0,0 +1,499 @@
|
||||
#0x0B:81
|
||||
0x0000:"No error"
|
||||
0x0001:"No controller"
|
||||
0x0002:"Feature not supported"
|
||||
0x0003:"Controller not supported"
|
||||
0x0004:""
|
||||
0x0005:"Invalid driver control code"
|
||||
0x0006:"Invalid firmware opcode"
|
||||
0x0007:"Memory allocation failed"
|
||||
0x0008:"Invalid controller ID"
|
||||
0x0009:"Invalid unit ID"
|
||||
0x000A:"Invalid drive ID"
|
||||
0x000B:"Invalid port ID"
|
||||
0x000C:"Driver not loaded"
|
||||
0x000D:"Retrieving unit descriptor"
|
||||
0x000E:""
|
||||
0x000F:""
|
||||
0x0010:"Failed to get unit status"
|
||||
0x0011:"Failed to get percentage complete"
|
||||
0x0012:"Failed to get drive from unit ID"
|
||||
0x0013:"Failed to get drive list from unit ID"
|
||||
0x0014:"Failed to remove drive"
|
||||
0x0015:"Failed to notify OS of unit change"
|
||||
0x0016:"Failed to get unit capacity"
|
||||
0x0017:"Port in use"
|
||||
0x0018:"Scan invalid port"
|
||||
0x0019:"Configuration not supported"
|
||||
0x001A:"Invalid number of drives"
|
||||
0x001B:"Invalid stripe size"
|
||||
0x001C:"Drives not from same controller"
|
||||
0x001D:"Duplicate drive"
|
||||
0x001E:"Port empty"
|
||||
0x001F:"One or more of the specified drives belong to another unit"
|
||||
0x0020:"Drive error"
|
||||
0x0021:"Invalid configuration"
|
||||
0x0022:"Failed to get unit ID"
|
||||
0x0023:"Invalid grouping"
|
||||
0x0024:"No drives specified"
|
||||
0x0025:"Can't import multiple drives"
|
||||
0x0026:"Drives not from same controller"
|
||||
0x0027:"Port empty"
|
||||
0x0028:"Drive error"
|
||||
0x0029:"Drive in use"
|
||||
0x002A:"Write cache not supported"
|
||||
0x002B:"No unit"
|
||||
0x002C:"Unit has no subunits"
|
||||
0x002D:"Invalid task rate"
|
||||
0x002E:"Port empty"
|
||||
0x002F:"Port busy"
|
||||
0x0030:"Remove operation invalid for unit"
|
||||
0x0031:"Unit is ok"
|
||||
0x0032:"Unit is rebuilding"
|
||||
0x0033:"Unit busy"
|
||||
0x0034:"Rebuild operation invalid for unit configuration"
|
||||
0x0035:"Replacement drive configuration is invalid for rebuild operation"
|
||||
0x0036:"Replacement drive is too small for rebuild operation"
|
||||
0x0037:"Percentage invalid config"
|
||||
0x0038:"Can't remove drive from unit during verify operation"
|
||||
0x0039:"Invalid spinups value"
|
||||
0x003A:"Invalid stagger time value"
|
||||
0x003B:"No such unit to delete"
|
||||
0x003C:"Invalid stripe size for unit configuration"
|
||||
0x003D:"Drive ID list no unit"
|
||||
0x003E:"Port empty"
|
||||
0x003F:"No unit"
|
||||
0x0040:"Unit is not rebuilding"
|
||||
0x0041:"Duplicate drives in import unit drive list"
|
||||
0x0042:"Controller firmware too old for application"
|
||||
0x0043:"Application too old for controller firmware"
|
||||
0x0044:"Unit busy"
|
||||
0x0045:"Failed to remove device node; Are all filesystems unmounted?"
|
||||
0x0046:"Failed to add device node for new unit"
|
||||
0x0047:"Need to upgrade controller's driver or firmware"
|
||||
0x0048:"Invalid verify operation for the given unit mode"
|
||||
0x0049:"Verify operation invalid for unit configuration"
|
||||
0x004A:"Controller has no battery backup unit"
|
||||
0x004B:"Battery backup unit has no battery"
|
||||
0x004C:"Failed to get unit's initialization information"
|
||||
0x004D:"Invalid unit configuration for initialization information"
|
||||
0x004E:"Failed to get unit's task information"
|
||||
0x004F:"Invalid unit configuration for task information"
|
||||
0x0050:"Unit configuration is not a mirror"
|
||||
#0x03:187
|
||||
0x0100:"SGL entry contains zero data"
|
||||
0x0101:"Invalid command opcode"
|
||||
0x0102:"SGL entry has unaligned address"
|
||||
0x0103:"SGL size does not match command"
|
||||
0x0104:"SGL entry has illegal length"
|
||||
0x0105:"Command packet is not aligned"
|
||||
0x0106:"Invalid request ID"
|
||||
0x0107:"Duplicate request ID"
|
||||
0x0108:"ID not locked"
|
||||
0x0109:"LBA out of range"
|
||||
0x010A:"Logical unit not supported"
|
||||
0x010B:"Parameter table does not exist"
|
||||
0x010C:"Parameter index does not exist"
|
||||
0x010D:"Invalid field in CDB"
|
||||
0x010E:"Specified port has invalid drive"
|
||||
0x010F:"Parameter item size mismatch"
|
||||
0x0110:"Failed memory allocation"
|
||||
0x0111:"Memory request too large"
|
||||
0x0112:"Out of memory segments"
|
||||
0x0113:"Invalid address to deallocate"
|
||||
0x0114:"Out of memory"
|
||||
0x0115:"Out of heap"
|
||||
0x0120:"Double degrade"
|
||||
0x0121:"Drive not degraded"
|
||||
0x0122:"Reconstruct error"
|
||||
0x0123:"Replace not accepted"
|
||||
0x0124:"Drive capacity too small"
|
||||
0x0125:"Sector count not allowed"
|
||||
0x0126:"No spares left"
|
||||
0x0127:"Reconstruct error"
|
||||
0x0128:"Unit is offline"
|
||||
0x0129:"Cannot update status to DCB"
|
||||
0x012A:"Dchnl cannot be split"
|
||||
0x012B:"Dchnl cannot be joined"
|
||||
0x012C:"No migration recovery"
|
||||
0x0130:"Invalid stripe handle"
|
||||
0x0131:"Handle that was not locked"
|
||||
0x0132:"Handle that was not empy"
|
||||
0x0133:"Handle has different owner"
|
||||
0x0140:"IPR has parent"
|
||||
0x0150:"Illegal Pbuf address alignment"
|
||||
0x0151:"Illegal Pbuf transfer length"
|
||||
0x0152:"Illegal Sbuf address alignment"
|
||||
0x0153:"Illegal Sbuf transfer length"
|
||||
0x0160:"Command packet too large"
|
||||
0x0161:"SGL exceeds maximum length"
|
||||
0x0162:"SGL has too many entries"
|
||||
0x0170:"Insufficient resources for rebuilder"
|
||||
0x0171:"Verify error (data != parity)"
|
||||
0x0180:"Requested segment not in directory of this DCB"
|
||||
0x0181:"DCB segment has unsupported version"
|
||||
0x0182:"DCB segment has checksum error"
|
||||
0x0183:"DCB support (settings) segment invalid"
|
||||
0x0184:"DCB UDB (unit descriptor block) segment invalid"
|
||||
0x0185:"DCB GUID (globally unique identifier) segment invalid"
|
||||
0x01A0:"Could not clear Sbuf"
|
||||
0x01C0:"Flash identify failed"
|
||||
0x01C1:"Flash out of bounds"
|
||||
0x01C2:"Flash verify error"
|
||||
0x01C3:"Flash file object not found"
|
||||
0x01C4:"Flash file already present"
|
||||
0x01C5:"Flash file system full"
|
||||
0x01C6:"Flash file not present"
|
||||
0x01C7:"Flash file size error"
|
||||
0x01C8:"Bad flash file checksum"
|
||||
0x01CA:"Corrupt flash file system detected"
|
||||
0x01CB:"Flash file has no component directory"
|
||||
0x01CC:"Flash file component not found"
|
||||
0x01D0:"Invalid field in parameter list"
|
||||
0x01D1:"Parameter list length error"
|
||||
0x01D2:"Parameter item is not changeable"
|
||||
0x01D3:"Parameter item is not saveable"
|
||||
0x0200:"UDMA CRC error"
|
||||
0x0201:"Internal CRC error"
|
||||
0x0202:"Data ECC error"
|
||||
0x0203:"ADP level 1 error"
|
||||
0x0204:"Port timeout"
|
||||
0x0205:"Drive power on reset"
|
||||
0x0206:"ADP level 2 error"
|
||||
0x0207:"Soft reset failed"
|
||||
0x0208:"Drive not ready"
|
||||
0x0209:"Unclassified port error"
|
||||
0x020A:"Drive aborted command"
|
||||
0x0210:"Internal CRC error"
|
||||
0x0211:"PCI abort error"
|
||||
0x0212:"PCI parity error"
|
||||
0x0213:"Port handler error"
|
||||
0x0214:"Token interrupt count error"
|
||||
0x0215:"Timeout waiting for PCI transfer"
|
||||
0x0216:"Corrected buffer ECC"
|
||||
0x0217:"Uncorrected buffer ECC"
|
||||
0x0230:"Unsupported command during flash recovery"
|
||||
0x0231:"Next image buffer expected"
|
||||
0x0232:"Binary image architecture incompatible"
|
||||
0x0233:"Binary image has no signature"
|
||||
0x0234:"Binary image has bad checksum"
|
||||
0x0235:"Binary image overflowed buffer"
|
||||
0x0240:"I2C device not found"
|
||||
0x0241:"I2C transaction aborted"
|
||||
0x0242:"SO-DIMM parameter(s) incompatible using defaults"
|
||||
0x0243:"SO-DIMM unsupported"
|
||||
0x0248:"SPI transfer status error"
|
||||
0x0249:"SPI transfer timeout error"
|
||||
0x0250:"Invalid unit descriptor size"
|
||||
0x0251:"Unit descriptor size exceeds data buffer"
|
||||
0x0252:"Invalid value in unit descriptor"
|
||||
0x0253:"Inadequate disk space to support descriptor"
|
||||
0x0254:"Unable to create data channel for this unit descriptor"
|
||||
0x0255:"CreateUnit descriptor specifies a drive already in use"
|
||||
0x0256:"Unable to write configuration to all disks during CreateUnit"
|
||||
0x0257:"CreateUnit/MigrateUnit does not support this descriptor version"
|
||||
0x0258:"Invalid subunit for RAID 0 or 5 in CreateUnit/MigrateUnit"
|
||||
0x0259:"Too many descriptors in CreateUnit/MigrateUnit"
|
||||
0x025A:"Invalid configuration specified in unit descriptor"
|
||||
0x025B:"Invalid LBA offset specified in unit descriptor"
|
||||
0x025C:"Invalid stripelet size specified in unit descriptor"
|
||||
0x025D:"JBOD unit is not allowed"
|
||||
0x0260:"SMART attribute exceeded threshold"
|
||||
0x0270:"Unit is not in NORMAL state"
|
||||
0x0271:"Invalid drive members"
|
||||
0x0272:"Converted unit is not supported"
|
||||
0x0300:"Internal errorcode (BBU base) - should not occur"
|
||||
0x0301:"Invalid BBU state change request"
|
||||
0x0302:"The BBU resource needed is in use; retry command after a delay"
|
||||
0x0310:"BBU command packet error"
|
||||
0x0311:"BBU command not implemented"
|
||||
0x0312:"BBU command buffer underflow"
|
||||
0x0313:"BBU command buffer overflow"
|
||||
0x0314:"BBU command incomplete"
|
||||
0x0315:"BBU command checksum error"
|
||||
0x0316:"BBU command timeout"
|
||||
0x0320:"BBU parameter not defined"
|
||||
0x0321:"BBU parameter size mismatch"
|
||||
0x0322:"Cannot write a read-only BBU parameter"
|
||||
0x0323:"BBU firmware version string not found"
|
||||
0x0324:"BBU operating state not available"
|
||||
0x0325:"BBU not present"
|
||||
0x0326:"BBU not ready"
|
||||
0x0327:"BBU S1 not compatible with HBA"
|
||||
0x0328:"BBU S0 not compatible with HBA"
|
||||
0x0329:"BBU not compatible with HBA"
|
||||
0x032A:"BBU not in S0"
|
||||
0x032B:"BBU not in S1"
|
||||
0x032C:"Timeout on BBU power fail interrupt"
|
||||
0x032D:"BBU command checksum error"
|
||||
0x0330:"Log updates not allowed"
|
||||
0x0331:"Logs are invalid"
|
||||
0x0332:"Logs not found"
|
||||
0x1000:""
|
||||
0x1001:""
|
||||
0x1002:""
|
||||
0x1003:"No stream available"
|
||||
0x1004:"Error during deallocate"
|
||||
0x1005:"Error during deallocate"
|
||||
0x1006:""
|
||||
0x1007:""
|
||||
0x1008:"Drive has been added"
|
||||
0x1009:"Drive has been removed"
|
||||
0x1010:"Error recovery in progress"
|
||||
0x1011:"Error recovery complete"
|
||||
0x1012:"No LBA to repair sector"
|
||||
0x1013:"Retry recovery step"
|
||||
0x1014:"Do error action"
|
||||
0x1015:"Degrade unit"
|
||||
0x1016:"Sector repair was not completed"
|
||||
0x1020:"Simulate power fail"
|
||||
0x2000:"Checksum of cache meta data is bad"
|
||||
0x2001:"Signature of cache meta data is bad"
|
||||
0x3013:"Data integrity error in diagnostic test"
|
||||
0x3014:"Undefined Sub-command for diag test"
|
||||
0x301E:"iHandler was busy before diag test"
|
||||
0x3021:"An unimplemented method was invoked"
|
||||
0x3024:"Data lines shorted in Sbuf RAM"
|
||||
0x3025:"Data lines open in Sbuf RAM"
|
||||
0x3026:"Addr line problem in Sbuf RAM"
|
||||
0x3027:"Sbuf RAM unreadable"
|
||||
0x3047:"Can't fill Sbuf with zeros"
|
||||
0x3062:"iHandler error during xfer op"
|
||||
0x3063:"Bad disk sequencer cmd issued to Aport"
|
||||
0x3064:"Bad RAM location"
|
||||
0x3065:"Bad Shadowed RAM location"
|
||||
0x3066:"Can't determine Sbuf size"
|
||||
0x3067:"Pbuf read/write error"
|
||||
0x3068:"XOR error"
|
||||
0x3069:"No disk found on requested Aport"
|
||||
0x306A:"Interrupt line error"
|
||||
0x306B:"Unable to calculate checksum"
|
||||
#0x0E:77
|
||||
0x00C4:"Invalid port map"
|
||||
:""
|
||||
0x00CF:"Invalid unit number"
|
||||
0x00D2:"Unsupported opcode"
|
||||
0x00DB:"Unsupported command"
|
||||
0x02C6:"Firmware command queue full"
|
||||
0x03C1:"SGL offset invalid"
|
||||
0x04C1:"SGL has too many entries"
|
||||
0x05C8:"Out of heap memory"
|
||||
0x06C8:"PCI read error"
|
||||
0x07C8:"Timeout waiting for PCI transfer"
|
||||
0x08C8:"PCI parity / abort error"
|
||||
0x09C7:"Unclassified port error"
|
||||
0x0BC1:"SGL read error in slow command"
|
||||
:""
|
||||
0x0EC1:"Invalid size in slow command"
|
||||
0x0FC1:"Duplicate request ID"
|
||||
0x10C1:"SGL size does not match command"
|
||||
0x10C4:"SGL size does not match command"
|
||||
0x11C1:"LBA out of range"
|
||||
0x12C8:"Command packet is not aligned"
|
||||
0x13C7:"Data integrity error in diagnostics test"
|
||||
0x14C1:"Invalid command in diagnostics test"
|
||||
0x14CB:"Invalid param in remove print"
|
||||
0x15C1:"Parameter table does not exist"
|
||||
0x16C1:"Parameter index does not exist"
|
||||
0x18C1:"SGL entry has unaligned address"
|
||||
0x19C1:"Invalid apchip in diagnostics test"
|
||||
0x1BC7:"Port timeout"
|
||||
0x1EC8:"PCI interface busy before transfer"
|
||||
0x20DB:"Parameter index 0 does not exist"
|
||||
0x21DB:"Invalid command for this datachannel"
|
||||
0x24C7:"Data lines shorted in Sbuf RAM"
|
||||
0x25C7:"Data lines open in Sbuf RAM"
|
||||
0x26C7:"Addr line problem in Sbuf RAM"
|
||||
0x27C7:"Sbuf RAM unreadable"
|
||||
0x28C4:"SGL required"
|
||||
0x29C4:"PUN table full"
|
||||
0x2BC1:"Diagnostic test firmware not found"
|
||||
0x2CC8:"Nested internal request"
|
||||
0x2DC1:"Error in upgrade image"
|
||||
0x2EC1:"Error programming flash ROM"
|
||||
0x2FC5:"Disk error during rollcall"
|
||||
0x30C5:"Timeout waiting for drive ready"
|
||||
0x31C4:"Invalid value in CreateUnit descriptor"
|
||||
0x31DB:"Invalid configuration in CreateUnit descriptor"
|
||||
0x32C4:"Invalid unit type in ReplaceDrive command"
|
||||
0x35C7:"Error writing one or more DCBs"
|
||||
0x36C1:"Error running disk profiler"
|
||||
0x37CB:"Unit is offline"
|
||||
0x3BC4:"Verify failed because array was never initialized"
|
||||
0x3CC4:"Verify failed"
|
||||
0x3CC7:"Verify failed"
|
||||
0x3EC1:"Physical drive is not a member of this unit"
|
||||
0x3EC4:"Logical drive is not a member of this unit"
|
||||
:""
|
||||
0x40C4:"Replace drive capacity too small"
|
||||
0x41C4:"No drive detected"
|
||||
0x42C4:"Drive detected but was busy"
|
||||
0x43C4:"Invalid aport in command"
|
||||
0x47C7:"Can't fill Sbuf with zeros"
|
||||
0x48C1:"Byte count exceeded maximum"
|
||||
0x49C1:"Timeout waiting for display to respond"
|
||||
0x4AC7:"Internal CRC error"
|
||||
0x4BC7:"PCI FIFO overrun detected"
|
||||
0x01C7:"Address mark not found"
|
||||
0x04C7:"Aborted command"
|
||||
0x10C7:"ID not found"
|
||||
0x40C7:"Uncorrectable data ECC"
|
||||
0x61C7:"Device fault"
|
||||
0x84C7:"UDMA CRC error"
|
||||
0x05C7:"SATA CRC error"
|
||||
0x0CC7:"SATA CRC error"
|
||||
0x14C7:"SATA CRC error"
|
||||
0xD0C7:"Device busy"
|
||||
0xD1C7:"Device busy"
|
||||
0x51C7:"Unclassified disk error"
|
||||
#0x04:99
|
||||
0x0000:"AEN queue empty"
|
||||
0x0001:"Controller reset occurred"
|
||||
0x0002:"Degraded unit detected"
|
||||
0x0003:"Controller error occured"
|
||||
0x0004:"Background rebuild failed"
|
||||
0x0005:"Background rebuild done"
|
||||
0x0006:"Incomplete unit detected"
|
||||
0x0007:"Background initialize done"
|
||||
0x0008:"Unclean shutdown detected"
|
||||
0x0009:"Drive timeout detected"
|
||||
0x000A:"Drive error detected"
|
||||
0x000B:"Rebuild started"
|
||||
0x000C:"Background initialize started"
|
||||
0x000D:"Entire logical unit was deleted"
|
||||
0x000E:"Background initialize failed"
|
||||
0x000F:"SMART attribute exceeded threshold"
|
||||
0x0010:"Power supply reported AC under range"
|
||||
0x0011:"Power supply reported DC out of range"
|
||||
0x0012:"Power supply reported a malfunction"
|
||||
0x0013:"Power supply predicted malfunction"
|
||||
0x0014:"Battery charge is below threshold"
|
||||
0x0015:"Fan speed is below threshold"
|
||||
0x0016:"Temperature sensor is above threshold"
|
||||
0x0017:"Power supply was removed"
|
||||
0x0018:"Power supply was inserted"
|
||||
0x0019:"Drive was removed from a bay"
|
||||
0x001A:"Drive was inserted into a bay"
|
||||
0x001B:"Drive bay cover door was opened"
|
||||
0x001C:"Drive bay cover door was closed"
|
||||
0x001D:"Product case was opened"
|
||||
0x0020:"Prepare for shutdown (power-off)"
|
||||
0x0021:"Downgrade UDMA mode to lower speed"
|
||||
0x0022:"Upgrade UDMA mode to higher speed"
|
||||
0x0023:"Sector repair completed"
|
||||
0x0024:"Sbuf memory test failed"
|
||||
0x0025:"Error flushing cached write data to disk"
|
||||
0x0026:"Drive reported data ECC error"
|
||||
0x0027:"DCB has checksum error"
|
||||
0x0028:"DCB version is unsupported"
|
||||
0x0029:"Background verify started"
|
||||
0x002A:"Background verify failed"
|
||||
0x002B:"Background verify done"
|
||||
0x002C:"Bad sector overwritten during rebuild"
|
||||
0x002D:"Background rebuild error on source drive"
|
||||
0x002E:"Replace failed because replacement drive too small"
|
||||
0x002F:"Verify failed because array was never initialized"
|
||||
0x0030:"Unsupported ATA drive"
|
||||
0x0031:"Synchronize host/controller time"
|
||||
0x0032:"Spare capacity is inadequate for some units"
|
||||
0x0033:"Background migration started"
|
||||
0x0034:"Background migration failed"
|
||||
0x0035:"Background migration done"
|
||||
0x0036:"Verify detected and fixed data/parity mismatch"
|
||||
0x0037:"SO-DIMM incompatible"
|
||||
0x0038:"SO-DIMM not detected"
|
||||
0x0039:"Corrected Sbuf ECC error"
|
||||
0x003A:"Drive power on reset detected"
|
||||
0x003B:"Background rebuild paused"
|
||||
0x003C:"Background initialize paused"
|
||||
0x003D:"Background verify paused"
|
||||
0x003E:"Background migration paused"
|
||||
0x003F:"Corrupt flash file system detected"
|
||||
0x0040:"Flash file system repaired"
|
||||
0x0041:"Unit number assignments were lost"
|
||||
0x0042:"Error during read of primary DCB"
|
||||
0x0043:"Latent error found in backup DCB"
|
||||
0x0044:"Cached write data is lost"
|
||||
0x0045:"Voltage is within normal range"
|
||||
0x0046:"Voltage is in low warning range"
|
||||
0x0047:"Voltage is in high warning range"
|
||||
0x0048:"Voltage is below operating range"
|
||||
0x0049:"Voltage is above operating range"
|
||||
0x004A:"Temperature is within normal range"
|
||||
0x004B:"Temperature is in low warning range"
|
||||
0x004C:"Temperature is in high warning range"
|
||||
0x004D:"Temperature is below operating range"
|
||||
0x004E:"Temperature is above operating range"
|
||||
0x004F:"Low current test started"
|
||||
0x0050:"Low current test stopped"
|
||||
0x0051:"High current test started"
|
||||
0x0052:"High current test stopped"
|
||||
0x0053:"Charge termination voltage is at high level"
|
||||
0x0054:"Charge termination voltage is at high level"
|
||||
0x0055:"Charge started"
|
||||
0x0056:"Charge stopped"
|
||||
0x0057:"Charge is in fault condition"
|
||||
0x0058:"Capacity is below warning level"
|
||||
0x0059:"Capacity is below error level"
|
||||
0x005A:"Battery is present"
|
||||
0x005B:"Battery is not present"
|
||||
0x005C:"High current test is in warning level"
|
||||
0x005D:"High current test is in error level"
|
||||
0x0060:"Bad cache meta data checksum"
|
||||
0x0061:"Bad cache meta data signature"
|
||||
0x0052:"Cache meta data restored from SBUF fail"
|
||||
0x00FC:"Recovered/finished array membership update"
|
||||
0x00FD:"Handler lockup"
|
||||
0x00FE:"Retrying PCI transfer"
|
||||
0x00FF:"AEN queue is full"
|
||||
#0x0F:31
|
||||
0x0000:"3AEN queue empty"
|
||||
0x0001:"3Soft reset occurred"
|
||||
0x0002:"1Unit degraded: Unit #"
|
||||
0x0004:"1Controller error"
|
||||
0x0005:"1Rebuild failed: Unit #"
|
||||
0x0003:"3Rebuild complete: Unit #"
|
||||
0x0006:"1Incomplete unit detected: Unit #"
|
||||
0x0007:"3Initialization complete: Unit #"
|
||||
0x0008:"2Unclean shutdown detected: Unit #"
|
||||
0x0009:"2ATA port timeout: Port #"
|
||||
0x000A:"1Drive error: Port #"
|
||||
0x000B:"3Rebuild started: Unit #"
|
||||
0x000C:"3Initialization started: Unit #"
|
||||
0x000D:"1Logical unit deleted: Unit #"
|
||||
0x000F:"2SMART threshold exceeded: Port #"
|
||||
0x0021:"2ATA UDMA downgrade: Port #"
|
||||
0x0022:"2ATA UDMA upgrade: Port #"
|
||||
0x0023:"2Sector repair occurred: Port #"
|
||||
0x0024:"1SBUF integrity check failure"
|
||||
0x0025:"1Lost cached write: Port #"
|
||||
0x0026:"1Drive ECC error detected: Port #"
|
||||
0x0027:"1DCB checksum error: Port #"
|
||||
0x0028:"1DCB unsupported version: Port #"
|
||||
0x0029:"3Verify started: Unit #"
|
||||
0x002A:"1Verify failed: Port #"
|
||||
0x002B:"3Verify complete: Unit #"
|
||||
0x002C:"2Overwrote bad sector during rebuild: Port #"
|
||||
0x002D:"1Encountered bad sector during rebuild: Port #"
|
||||
0x002E:"1Replacement drive is too small: Port #"
|
||||
0x002F:"2Verify error: Unit not previously initialized: Unit #"
|
||||
0x0030:"1Drive not supported: Port #"
|
||||
#0x07:8
|
||||
0x1001:"Not locked"
|
||||
0x1002:"Already locked"
|
||||
0x1003:"No more events"
|
||||
0x1004:"AEN clobber occurred"
|
||||
0x8001:"unknown IOCTL request"
|
||||
0x8002:"insufficient length parameter"
|
||||
0x8003:"firmware failed initialization"
|
||||
0x8004:"internal error in driver at:"
|
||||
#0x06:4
|
||||
0x1001:"Not locked"
|
||||
0x1002:"Already locked"
|
||||
0x1003:"No more events"
|
||||
0x1004:"AEN clobber occurred"
|
||||
#0x05:4
|
||||
0x1003:"No more events"
|
||||
0x1004:"AEN clobber occurred"
|
||||
0x1001:"Not locked"
|
||||
0x1002:"Already locked"
|
||||
Reference in New Issue
Block a user